Setaflash Series 3 ActiveCool Flash Point Tester
Note : Due to distribution agreements, Paragon Scientific may be restricted as to where these products can be sold to. We kindly advise you to contact the Sales team directly at firstname.lastname@example.org with your requirements.
Setaflash Series 3 ActiveCool Flash Point Tester
Part No: 33200-3
The Setaflash Series 3 ActiveCool Small Scale Flash Point Tester is the latest instrument in the Setaflash range. It has been designed to rapidly and efficiently carry out Flash / No Flash tests to determine the flash point of liquids and semi-solids in the 10 to 130°C (50 to 266°F) temperature range.
When used in Ramp mode the temperature of the sample increases at a rate of 2°C/min. An audible prompt to carry out a flash test occurs every 1°C rise up to 100°C (every 2°C rise above 100°C), until a flash is detected, allowing rapid determination of a flash point in accordance with ASTM D7236 and IP 534. The sample cup is heated / cooled by peltier cells. This gives very accurate and stable sub-ambient test temperatures and the benefit of rapid temperature normalisation between tests.
All functions on the Series 3 flash point tester are accessed via a two button keypad and the Seta Multifunctional And Rotational Test (SMART) control feature. The digital display shows test parameters, instrument status, and the test result. An audible prompt is sounded when an action is required from the operator. Gas for the test jet/shutter assembly is supplied from an integral gas tank, which is filled using a standard butane (lighter) refill cartridge.
The automatic flash detection system is tuned to ignore halo and other false flash effects, reducing the chance of mis-interpretation of the test result, and enhancing repeatability. Barometric pressure is measured by an internal barometer, and the correction is automatically applied to the test result.
The instrument is lightweight and suitable for mobile use when operated from the optional DC power adaptor.
Supplied with: 2ml syringe, mains lead and instruction manual.
|Temperature Range||10 to 130°C (50 to 266°F)|
|Test Modes||Rapid Equilibrium and Ramp|
|Sample Size||2ml for flash points up to 100°C 4ml for flash points above 100°C|
|Test Duration, Rapid Equilibrium Mode||1 minute below 100°C, 2 minutes above 100°C, or user determined 1 to 99 minutes|
|Ramp Rate||2°C/min ramp|
|Heating and Cooling System||Peltier Cell|
|Voltage||100/240V, 50/60Hz (switchable) 12Vdc with optional power adaptor|
|Gas Supply||Laboratory gas, 3kPa (0.44psi) maximum pressure or Butane from optional Portable Gas Tank 13667-0|
|Size (HxWxD)||26 x 28 x 26cm|
|CCCN Code:||Tariff 90268020|
- Flash / No Flash & Ramp modes
- 10 to 130°C temperature range
- Flash point test in less than 2 minutes
- Small sample size (2 or 4ml)
- Automatic flash detection
- Electronic peltier cooling
- Audible and on-screen prompts
- Portable operation
- °C or °F display
ASTM D3278, ASTM D3828, ASTM D7236, ASTM E502, BS 3900 Part A13, BS 6664 Parts 3 & 4, BS EN 456, CHIPS Regulations, Classification of Dangerous Goods for Carriage: Viscous and Non-viscous Liquids, EPA 1020 A & B, IP 303 (obs), IP 523, IP 524, IP 534, ISO 3679, ISO 3680, UN Class 3 Non-viscous Flammable Liquids
DETAILS OF METHODS
|CHIPS Regulations||Chemicals Hazard Information and Packaging for Supply|
|Classification of Dangerous Goods for Carriage: Viscous and Non-viscous Liquids||The Multiflash-SS fully automates and conforms precisely to national and international Small Scale Closed Cup standard test methods.|
|EPA 1020 A & B||Setaflash Closed-Cup Method for determining ignitability|
|ASTM D3828||Standard Test Methods for Flash Point by Small Scale Closed Tester|
|IP 303 (obs)||Determination of flash point -Part 1 - Rapid equilibrium closed cup method. Part 2 - Flash / no flash test - Rapid equilibrium closed cup method|
|ASTM D3278||Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus - The test methods are applicable to paints, enamels, lacquers, varnishes, and related products having a flash point between 0 and 110°C (32 and 230°F) and Viscosity lower than 150 St at 25°C (77°F).|
|BS EN 456||Method for determination of flashpoint of paints, varnishes and related products by the rapid equilibrium method|
|ISO 3680||Methods of test for paints. Tests on liquid paints (excluding chemical tests). Test for flash/no flash (rapid equilibrium method)|
|UN Class 3 Non-viscous Flammable Liquids||Small scale flash point testers are universally specified in many international regulations to define and classify "flammable" and "combustible" substances.|
|ASTM E502||Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods|
|ISO 3679||Determination of flash point. Rapid equilibrium closed cup method|
|BS 6664 Parts 3 & 4||Methods of test for paints. Tests on liquid paints (excluding chemical tests). Test for flash/no flash (closed cup equilibrium method)|
|BS 3900 Part A13||Test for flash/no flash (rapid equilibrium method)|
|IP 523||Determination of flash point. Rapid equilibrium closed cup method|
|IP 524||Methods of test for paints. Tests on liquid paints (excluding chemical tests). Test for flash/no flash (rapid equilibrium method)|
|ASTM D7236||Flash Point by Small Scale Closed Cup Ramp Method|
|IP 534||Flash Point by Small Scale Closed Cup Ramp Method|
|Lead Time||4 - 6 Weeks|
|Dimensions cm (WxDxH)||(HxWxD): 26 x 28 x 26cm|
|PDF's||Flash Point Information Sheet|